Sebastian Spintzyk

Tuebingen, BW 72076, Germany

Last Updated: 09/26/2026

Save publications for later

Sign Up

Not sure about your diagnosis?

Check Your Symptoms

Found 69 publications

Evaluation of fracture strength and failure mode of zirconia molar implant abutments manufactured with additive and subtractive manufacturing technologies.

Evaluation of fracture strength and failure mode of zirconia molar implant abutments manufactured with additive and subtractive manufacturing technologies.

Journal: The Journal of prosthetic dentistry

Published: November 08, 2025

Evaluation of surface roughness and cell viability of milled and printed polyetheretherketone healing abutments: a comparative study.

Evaluation of surface roughness and cell viability of milled and printed polyetheretherketone healing abutments: a comparative study.

Journal: Odontology

Published: October 29, 2025

Marginal gap of printed, milled, and heat-pressed two-piece polyetheretherketone abutments before and after thermal cycling, and their pull-off bond strength after thermal cycling.

Marginal gap of printed, milled, and heat-pressed two-piece polyetheretherketone abutments before and after thermal cycling, and their pull-off bond strength after thermal cycling.

Journal: Journal of prosthodontics : official journal of the American College of Prosthodontists

Published: March 03, 2025

Investigating the influence of infill pattern and layer height on the mechanical and bonding behavior of additively manufactured PEEK for dental applications.

Investigating the influence of infill pattern and layer height on the mechanical and bonding behavior of additively manufactured PEEK for dental applications.

Journal: The Journal of prosthetic dentistry

Published: November 11, 2024

Cytocompatibility of Polymers for Skin-Contact Applications Produced via Pellet Extrusion.

Cytocompatibility of Polymers for Skin-Contact Applications Produced via Pellet Extrusion.

Journal: Journal of functional biomaterials

Published: May 17, 2024

Dimensional Stability of Additively Manufactured Dentate Maxillary Diagnostic Casts in Biobased Model Resin.

Dimensional Stability of Additively Manufactured Dentate Maxillary Diagnostic Casts in Biobased Model Resin.

Journal: Materials (Basel, Switzerland)

Published: April 10, 2024

Positional accuracy of a single implant analog in additively manufactured casts in biobased model resin.

Positional accuracy of a single implant analog in additively manufactured casts in biobased model resin.

Journal: Journal of dentistry

Published: March 28, 2024

Conventionally and digitally fabricated removable complete dentures: manufacturing accuracy, fracture resistance and repairability.

Conventionally and digitally fabricated removable complete dentures: manufacturing accuracy, fracture resistance and repairability.

Journal: Dental materials : official publication of the Academy of Dental Materials

Published: February 20, 2024

The effect of thermomechanical aging on the fracture resistance of additively and subtractively manufactured polyetheretherketone abutments.

The effect of thermomechanical aging on the fracture resistance of additively and subtractively manufactured polyetheretherketone abutments.

Journal: Journal of dentistry

Published: February 17, 2024

Post-processing of a 3D-printed denture base polymer: Impact of a centrifugation method on the surface characteristics, flexural properties, and cytotoxicity.

Post-processing of a 3D-printed denture base polymer: Impact of a centrifugation method on the surface characteristics, flexural properties, and cytotoxicity.

Journal: Journal of dentistry

Published: November 12, 2023

Three-Dimensional Printed Tooth Model with Root Canal Ledge: A Novel Educational Tool for Endodontic Training.

Three-Dimensional Printed Tooth Model with Root Canal Ledge: A Novel Educational Tool for Endodontic Training.

Journal: Dentistry journal

Published: July 30, 2023

Effects of layer thickness and build angle on the microbial adhesion of denture base polymers manufactured by digital light processing.

Effects of layer thickness and build angle on the microbial adhesion of denture base polymers manufactured by digital light processing.

Journal: Journal of prosthodontic research

Published: February 22, 2023

Showing 1-12 of 69

Last Updated: 09/26/2026