Tc-99M
What is Ultra-Technekow V4 (Tc-99M)?
Approved To Treat
Top Global Experts
Related Clinical Trials
Summary: This clinical trial tests how well molecular breast imaging (MBI) works to guide the collection of a breast biopsy in patients with a breast abnormality. Currently, a biopsy is often guided by either ultrasound or mammography in order to ensure that a sample of the correct part of the breast is taken. Sometimes a lesion or part of the lesion cannot be seen on ultrasound or mammography, and, theref...
Summary: This phase II trial studies how well personalized neck radiation therapy directed by sentinel lymph node biopsy (SLNB) works in treating patients with oral cavity squamous cell carcinoma (OCSCC). SLNB can be performed as part of standard care for OCSCC. During SLNB, a radiotracer is injected around the tumor. The lymph nodes are then biopsied and tested to see if the tracer injected into the tumor...
Summary: The objective of this study is to apply advanced diffusion imaging in a two-pronged assessment of renal mass patients: (1) characterization of lesion malignancy and subtype, and (2) prediction of renal function stability or decline following partial nephrectomy.
Related Latest Advances
Brand Information
- Lift the generator by its handle and place it inside the auxiliary shield. Move the handle so that it is not covering the generator top by pushing it off to the side in between the generator and the auxiliary shield.
- Remove and store the elution hood cover. Place the auxiliary shield top onto the top of the generator and align it with the elution hood.
- Remove and store the tip cap plugs from the needles.
- Remove the flip-top cap of the eluant vial; disinfect the stopper with a bacteriocide such as 70% isopropyl alcohol, allowing the stopper to dry before use. Invert the eluant vial and place stopper first into the saline vial alignment insert. Place the saline vial alignment insert and vial into the saline port of the auxiliary shield top and firmly push down the eluant vial until the stopper is punctured and seated at the base of the eluant needles.
- Place the saline shield on top of the auxiliary shield top to cover the eluant vial.
- Remove the flip-top cap of an evacuated vial; disinfect the stopper, allowing the stopper to dry before use. Place the evacuated vial into the elution tool.
- Position the shielded evacuated vial by carefully lowering the elution tool into place on the elution needle. Piercing the septum of the evacuated vial with the elution needle will begin the elution process.
- Wait until the evacuated vial has completely filled itself. This may take a few minutes.
- NOTE: Do not use generator eluate if its appearance is discolored, and discontinue use of the generator.
- Remove the flip-top cap of the Technestat vial; disinfect the stopper, allowing the stopper to dry before use. Secure the Technestat vial into the Technestat vial holder.
- Carefully remove the elution tool and replace with the shielded Technestat vial.
- Determine the technetium Tc-99m concentration and molybdenum Mo-99 content for dispensing purposes. The generator eluate may be assayed using an appropriate detection system. The manufacturer’s instructions for operation of the instrument/equipment should be followed for measurement of Technetium Tc-99m and Molybdenum Mo-99 activity.
- Determine the aluminum ion concentration of the eluate.
- Remove the saline shield and then remove saline vial alignment insert from the saline port to remove the eluant vial from the eluant needles. Remove the vial from the saline vial alignment insert and reuse the saline vial alignment insert for subsequent elutions.
- Remove the shielded Technestat vial by carefully lifting the Technestat vial shield from the elution needle.
- Repeat steps 4 through 12 of the Elution procedure above.
- Following the life of the generator, remove and dispose of the used Technestat vial and the eluant vial.
- Cover the elution and eluant needles with the stored tip cap plugs.
- Place the stored elution hood cover onto the top of the generator.
- The intact generator assembly should be either returned to Curium US LLC or disposed of in accordance with applicable regulations.
RADIOACTIVE MATERIAL
Maryland Heights, MO 63043
Made in USA/Fabriqué aux États-Unis/Hecho en E.U.A

RADIOACTIVE MATERIAL
Maryland Heights, MO 63043
Made in USA/Fabriqué aux États-Unis/Hecho en E.U.A

RADIOACTIVE MATERIAL
Maryland Heights, MO 63043
Made in USA/Fabriqué aux États-Unis/Hecho en E.U.A

RADIOACTIVE MATERIAL
Maryland Heights, MO 63043
Made in USA/Fabriqué aux États-Unis/Hecho en E.U.A

RADIOACTIVE MATERIAL
Maryland Heights, MO 63043
Made in USA/Fabriqué aux États-Unis/Hecho en E.U.A

RADIOACTIVE MATERIAL
Maryland Heights, MO 63043
Made in USA/Fabriqué aux États-Unis/Hecho en E.U.A

RADIOACTIVE MATERIAL
Maryland Heights, MO 63043
Made in USA/Fabriqué aux États-Unis/Hecho en E.U.A

RADIOACTIVE MATERIAL
Maryland Heights, MO 63043
Made in USA/Fabriqué aux États-Unis/Hecho en E.U.A

RADIOACTIVE MATERIAL
Maryland Heights, MO 63043
Made in USA/Fabriqué aux États-Unis/Hecho en E.U.A

RADIOACTIVE MATERIAL
Maryland Heights, MO 63043
Made in USA/Fabriqué aux États-Unis/Hecho en E.U.A

RADIOACTIVE MATERIAL
Maryland Heights, MO 63043
Made in USA/Fabriqué aux États-Unis/Hecho en E.U.A

RADIOACTIVE MATERIAL
Maryland Heights, MO 63043
Made in USA/Fabriqué aux États-Unis/Hecho en E.U.A

RADIOACTIVE MATERIAL
Maryland Heights, MO 63043
Made in USA/Fabriqué aux États-Unis/Hecho en E.U.A

